Mouse Grip Sticker for Logitech G102 / G203 / G304 / G305 / G Pro Wired

This Logitech G102 G203 grip sticker is a seven-piece precut set designed to turn a slippery stock shell into a mouse you can actually hold onto. Sweaty palms, a glossy finish and fast flicks are a bad combination, and grip tape fixes all three for a fraction of the cost of a new mouse. Moreover, the textured black surface carries a sharp industrial graphic print, so your setup gains some personality alongside the extra control.

Precut for the Logitech G102 G203 Grip Tape Shell Family

Logitech uses one identical shell across several of its most popular mice, which means a single set fits all of them. This grip tape is cut for the Logitech G102, the G203 in both Prodigy and Lightsync versions, the G304, the G305 and the wired G Pro. Because every piece is die-cut to the exact contours of that shell, the edges line up with the button seams and side rails instead of overhanging or leaving bare patches. Therefore you get a factory-fitted look rather than something trimmed by hand.

Textured Anti-Slip Surface

The surface uses a fine raised texture that gives your fingers something to bite into, even when your hands get warm mid-match. As a result, lift-offs feel more secure, hard flicks do not slide, and you stop subconsciously gripping harder to compensate. That last point matters more than it sounds, since a death grip tires your hand and makes micro-adjustments less precise over a long session.

Seven-Piece Coverage

The set includes seven precut pieces covering both side rails, both main click buttons and the top and rear shell sections. Consequently the areas your hand actually contacts are all covered, not just the sides. The button pieces are thin enough that click feel and travel stay intact, so your left and right clicks respond exactly as they did before. You can also apply only the pieces you want and keep the rest spare.

Easy to Apply, Clean to Remove

Installation takes a few minutes. First, wipe the shell clean and let it dry fully, since any oil left behind will stop the adhesive bonding properly. Then peel each piece off the backing sheet, line it up against the button seam or shell edge, and press it down firmly for about thirty seconds. Work one piece at a time rather than peeling everything at once. When you eventually want it off, the tape lifts away without tearing, although a little adhesive residue can remain and wipes off easily.

What This Grip Tape Does Not Fit

This is worth reading before you order. The set fits the wired G Pro only. It does not fit the G Pro Wireless, the G Pro X Superlight, the Superlight 2 or the G Pro 2 Lightspeed, because those use a completely different and larger shell despite the similar names. It also does not fit the G502, G402, G403, G703 or any other Logitech model. If you are unsure which mouse you own, check the model number printed on the underside of your mouse before ordering, or message us and we will confirm it for you.

Who Needs Grip Tape

Anyone whose hands get warm during long sessions benefits immediately, and that covers most players in Kathmandu through the warmer months. Claw and fingertip grippers gain the most, since those styles depend on side-rail friction to lift and reposition the mouse. In addition, players whose stock shell has gone shiny and slick with age get their original control back without replacing the mouse. It is one of the cheapest meaningful upgrades you can make to a setup.

Buy Logitech G102 G203 Grip Sticker in Nepal

Backseat Gaming stocks this grip sticker set with delivery across Nepal. Browse our full range of gaming mice and accessories if you are upgrading more than your grip, or check which Logitech models share this shell on the official Logitech G mice page. You are also welcome to drop by our Balkhu store and have it fitted.

Frequently Asked Questions

Which mice does this grip tape fit?

It fits the Logitech G102, G203 Prodigy, G203 Lightsync, G304, G305 and the wired G Pro. All six use the same shell, so one set covers them all.

Will it fit my G Pro X Superlight?

No. The G Pro X Superlight, Superlight 2, G Pro Wireless and G Pro 2 Lightspeed all use a different, larger shell than the wired G Pro. This set is cut for the smaller G102 and G203 family only, so the pieces will not line up.

Does grip tape affect how the buttons click?

Barely. The button pieces are thin, so click travel and tactility stay essentially the same. Most players stop noticing the tape within a day of use, while the extra friction on the sides remains obvious.

Can I remove it later without damaging my mouse?

Yes. The pieces peel off cleanly in one go. Some light adhesive residue may be left behind depending on how long it has been on, and that wipes away with isopropyl alcohol. Note that once removed, a piece will not stick as firmly if you try to reapply it.

How long does grip tape last?

With daily gaming, expect several months before the texture starts to smooth out in the highest-contact spots. Heavy sweat shortens that, while wiping the mouse down regularly extends it. Grip tape is a consumable, so plan on replacing it periodically.

How do I check which Logitech mouse I have?

Turn the mouse over. The model number is printed on the label on the underside, next to the regulatory markings. If the label has worn off, send us a photo of your mouse and we will identify it for you.