Glass Dot Skates — 6mm Universal Mouse Feet (8 Dots)

These glass dot skates replace the stock PTFE feet on your mouse with 6mm discs of tempered glass. The difference is immediate: glass glides faster, stays consistent instead of degrading, and lasts years rather than months. Moreover, each dot carries the Backseat Gaming logo sealed beneath the glass surface, so the branding never wears off no matter how many hours you put in.

Why Glass Dot Skates Outlast PTFE

Stock mouse feet are made from PTFE, which is soft by design. It glides well when new, but it abrades steadily against your mousepad and picks up grit along the way. Within a few months of daily use the glide has slowed, the edges have rounded unevenly, and the mouse no longer moves the way it did out of the box. Tempered glass does not wear like that. Because the surface is vastly harder than cloth or any pad coating, the glide you feel on day one is the glide you feel a year later. Consequently you stop treating mouse feet as a consumable altogether.

1.0mm Tempered Glass, Built as a Replacement

These dots are 1.0mm thick and are designed to replace your original feet, not sit on top of them. That distinction matters. Stock feet usually measure between 0.6mm and 0.8mm, so swapping them for 1.0mm glass keeps your mouse at a sensible height above the pad and your sensor inside its working range. Stacking skates on top of existing ones, by contrast, raises the mouse far enough to affect tracking and lift-off distance. Remove the old feet first and the geometry stays correct.

Chamfered Edges That Protect Your Mousepad

The glide surface is flat, while the edges are rounded off rather than left sharp. This is the detail that separates a well-made glass skate from a bad one. A flat face spreads the weight of the mouse across the full contact area, which keeps the glide even and predictable. Meanwhile the chamfered edge means nothing catches, digs in or scores your pad when you reposition the mouse. Cheap glass skates with square-cut edges do exactly that, and the damage shows up on a cloth pad within weeks.

Our Logo, Sealed Under the Glass

The Backseat Gaming logo sits on the underside of each dot, visible through the glass from below. Because the print is sealed beneath the surface rather than applied on top of it, friction never touches it. Therefore the branding looks exactly the same after a year of daily use as it did on the day you fitted it, while the face that meets your pad stays plain, smooth glass.

Universal 6mm Format

At 6mm across, these dots fit essentially any gaming mouse, because you choose the placement rather than relying on a die-cut shape matched to one shell. The pack contains eight dots, which covers the four standard corner positions on most mice with four left over as spares, or supports a denser eight-point layout on a larger shell. As a result, a single product works across your whole collection instead of needing a different SKU for every mouse you own.

How to Fit Your Glass Dot Skates

Start by peeling off the original feet, working a fingernail or a thin plastic card under one edge and lifting slowly. Next, wipe the entire base with the included alcohol pad to lift every trace of old adhesive, then let it dry fully, since residue is the main reason skates come loose later. Then position each glass dot where the original feet sat, keeping them symmetrical left to right so the mouse sits level. Finally, press each one down firmly for around thirty seconds. Take your time with placement, because an uneven layout causes a subtle rock that is far more annoying than it sounds.

Who They Suit, and Who They Do Not

Glass is a fast, low-friction glide, so it suits players who want speed and minimal resistance, and it works especially well on hard pads and smooth, fast cloth. However, it is worth being honest about the trade-off. Some players prefer the extra control and slight drag that PTFE gives on a soft, textured cloth pad, and glass can also run slightly louder across certain surfaces. If you have never tried glass before, expect an adjustment period of a few days while your aim recalibrates to the reduced friction. Most players who make the switch do not go back, but it is a change in feel rather than a straight upgrade for everyone.

Buy Glass Dot Skates in Nepal

These are made for Backseat Gaming and available with delivery across Nepal. Pair them with a mouse from our gaming mice collection, or come and feel the difference for yourself at our Balkhu store before you commit. We are happy to fit them for you in store.

Frequently Asked Questions

Will these fit my mouse?

Almost certainly. Dot skates are universal because you place them yourself rather than relying on a shape cut for one specific shell. Any gaming mouse with a flat base area where the original feet sat will take them.

Do I need to remove my original mouse feet?

Yes. These are 1.0mm replacements, not an addition. Fitting them on top of existing feet raises the mouse too far off the pad, which can affect sensor tracking and lift-off distance. Peel the old feet off and clean the base with the included alcohol pad first.

Are glass skates faster than PTFE?

Yes, noticeably. Glass has lower friction than PTFE and keeps that glide consistently instead of slowing as it wears. Whether faster is better depends on your preference, since some players want a little drag for control, but the speed difference itself is not subtle.

Will glass skates damage my mousepad?

Not with chamfered edges like these. Pad damage from glass skates comes from sharp, square-cut edges digging into the surface. A flat face with rounded edges spreads the load and slides over the weave instead of catching it.

How long do they last?

Far longer than PTFE, which typically needs replacing every few months with heavy use. Tempered glass is hard enough that it will usually outlast the mouse it is fitted to, so a single set is generally a one-time purchase.

What if my mouse has a ring around the sensor?

Some mice use a circular foot surrounding the sensor lens. Leave that one in place, since it also keeps dust away from the lens, and replace only the main corner feet. Alternatively, place the dots around it and keep the heights matched so the mouse sits level.